Arduino Projects    |   Raspberry Pi  |     Electronic Circuits   |   Electronics Reference Design Library  |   AVR    |    PIC    |    8051    |    Electronic Projects

USB Mobile Charger Circuit Diagram

Summary

By: 
Anjali Sethiya
Nowadays mobiles can also be charged using the USB outlet of PC. The mobile charger circuit presented in this project can give 4.7V of synchronized voltage for charging the phone. As USB outlets can give 5V DC and 100mA of current. It is sufficient for slow charging of mobile phones so they can be used to charge the mobile phones. USB stands for Universal Serial Port. It is one of the latest methods to exchange information from PC to the real world. The USB port offers power to the external devices. +5V of power is available at pin1 and -5V of it is available at pin4.
USB Mobile Charger

Description

 

Most of the Mobile Phones battery are rated 3.6 volts at 1000 to 1300 mAh. These battery sets have 3 Lithium cells which have 1.2 volt rating.

Typically a battery pack sufficiently requires 4.5 volts and 300-500 mA current for fast charging. But low current charging is preferred to increase the efficiency of the battery. The mobile phone charger circuit based project described here provides 4.7 V of the regulated voltage and a sufficient amount of current for the slow charging of the mobile phones. Regulated output is given by the transistor T1, output voltage is controlled by Zener diode ZD and the polarity of the output supply is protected by D1. Front end of the circuit should be connected to an A type USB plug, a red wire to pin1 and black wire to pin 4 of the plug for easy polarity recognition. The output of a suitable charger pin should be connected with the mobile phone. After the circuit is assembled, USB plug should be inserted into the socket and output should be measured from the circuit. If the output is OK and polarity is correct, connect it with the mobile phone and if the polarity is incorrect, it will destroy the mobile battery so extreme care should be taken.

 

For making this mobile charger circuit, a USB cable is used with at least one male plug on it and strip back about 5 cm of the outer insulation with shield from the bare end of the USB cable. Normally, USB cables have four wires i.e. red, green, white and black. As green and white carry the data so they can be trimmed as they have no use here.. Mostly black wire is NEGATIVE and red is POSITIVE. The voltage across USB is about 5V with 500 mA as maximum current for any device. Now power lines are connected to the USB plug with correct polarity. Reflectors are used for LEDs to get maximum illumination.

Circuit Diagram

Components

Resistor Image
Resistor

Resistor is a passive component used to control current in a circuit. Its resistance is given by the ratio of voltage applied across its terminals to the current passing through it. Thus a particular value of resistor, for fixed voltage, limits the current through it. They are omnipresent in electronic circuits.

...
Capacitor image
Capacitor

Capacitor is a passive component used to store charge. The charge (q) stored in a capacitor is the product of its capacitance (C) value and the voltage (V) applied to it. Capacitors offer infinite reactance to zero frequency so they are used for blocking DC components or bypassing the AC signals. The capacitor undergoes through a recursive cycle of charging and discharging in AC circuits where the voltage and curre...

BC547 | Transistor BC547  | PDF Datasheet
Transistor BC547
BC547 is an NPN bi-polar junction transistor. A transistor, stands for transfer of resistance, is commonly used to amplify current. A small current at its base controls a larger current...

Step-By-Step

Browse 4m+ Electronic Products


 
Pick the right product for your next design project with "Mouser Store". Mouser Electronics brings broadest range of semiconductors and electronic components from over 500 industry leading suppliers. 
 
Mouser specializes in the rapid introduction of new products and technologies for design engineers and buyers that includes semiconductors, interconnects, passives, and electro-mechanical components. Providing the best possible service with the flexibility of not requiring a minimum order and same-day shipping, Mouser has it all.
 
 
 
 
When you need the right part right now, think of Mouser
 
Thank you
Team EG

 

APPLICATIONS & TECHNOLOGIES

Learn about the latest applications and industry trends with tutorials and white paper design resources on vertical markets.

Automotive
Energy Harvesting
MEMS Technology
OpenSource Hardware
RFID & NFC
RF Wireless
Sensor
Solar
Touch
Wireless Charging

 

You are here