As a result, we have compiled a set of basic electronics skills for beginners that act as a pre-requisite for ensuring success. Moreover, you can utilize these while repairing a simple device or while working on your dream project. Basically, handling the electronics for a practical purpose can be really tough if you don’t know how to deal with the components involved.
So, without beating around the bush, let’s have a look at these 10 basic electronics skills for beginners -:
1. Knowledge about Basic Components
A circuit has a lot of components categorised as active and passive. The former ones provide and control current whereas the latter ones respond to the voltage flow and dissipate/store energy. Mainly, every electronic circuit has the following components -:
2. Breadboarding
You can have a detailed view of the different parts and working of a breadboard here.
As mentioned above, a breadboard is the most basic component of a circuit and is used for solderless prototyping which is particularly useful for beginners. Prototyping creates a preliminary model which is later used for testing followed by the development of the final model. Breadboards can easily accommodate a wide range of circuits ranging from the simple to the complex ones.
So, after getting on with a project, the first thing you are required to learn is to arrange the components on a breadboard along with the connecting wires.
3. Drawing Schematics
Schematics act as universal pictograms for understanding and building the electronics. Every component discussed in the list above (and others) have a specific symbol. These symbols are combined using a variety of programs. Schematics are important so as to design the circuits and there are a lot of online circuit design tools available for the users. These apps and software offer a virtual view of the breadboard where you can learn to combine all the components of a circuit.
4. Soldering
Even though you can take on solderless bread boarding but getting acquainted with the soldering technique can open up a lot of possibilities for an electronic project. Moreover, it’s easy to learn and can help in exploring a wide range of projects ranging from the simple ones to the complicated ones. In order to solder the components to a circuit, a soldering iron is used which contains the following parts -:
5. De-Soldering Tools
Note: You may read this article on soldering and de-soldering for details.
After learning the soldering skills one has to have a proper know-how of de-soldering as well. This is important for cases when you need to make changes in the circuit like for troubleshooting, repair or making any replacements. There are various tools for this purpose; usually, either a solder wick or vacuum pump is used along with the soldering iron.
In this process, the soldering iron is used to heat the part of the board where the de-soldering has to be applied and then a device is placed to suck or remove the unwanted component. It’s important to note that a soldering iron ranging between 15W-30W should be utilised because a higher wattage may damage the board as well as the components with the excess of heat.
6. Using a Multimeter
You may also read our Tutorial on using a multimeter for continuity.
A multimeter is an important tool for measuring voltage, current, resistance, and continuity of a circuit. It’s also used for testing a battery and for troubleshooting problems found in an electrical device. Basically, there are three parts of a multimeter including a display screen (for digital type), selection knob and a couple of ports.
Besides, the types of probes available for this tool also vary, such as alligator clips, IC hooks, test probes, and tweezers. These devices are available in a wide variety ranging from the low-cost ones with basic features to the expensive ones with advanced features like auto off and auto-ranging facilities.
7. Hot glue guns
Hot glue guns are very useful in electronic projects whenever there is a need to stick certain components. These guns contain plastic which acts as an insulator and hence reduces the chance of a short circuit. It’s available at a low cost and is easy to use.
The kit offers a gun and some glue sticks which are inserted in the gun. After that when the trigger is pulled, the hot glue drips out of the nozzle. However, because of the heated glue, it’s important to be cautious as an excess of heat may damage your board and components. Another important thing is to keep the nozzle clean by removing any glue residue with the help of an aluminum foil.
8. Liquid electrical tape
It’s a rubber fluid compound which is mainly used when the insulation of a wire is broken. It prevents moisture to enter the place and is quite easy to apply. Before using it, one has to make sure that the place is completely free of moisture and there are no cracks or loose portions.
To make use of this tape, just stir the liquid and spread it over the desired place with the help of a brush. It’s important to note that 30% of its compounds are volatile and hence it should not be brought near any kind of open flame. It’s a great replacement for electrical tape and heat shrink tapes at tight enclosures.
9. Testing
Apart from the measurement of voltage, current, and resistance; there are various stages where one has to conduct tests so as to make sure that everything is going on correctly with the project. At first, the continuity test is performed in Off position to ensure that one point of the board is connected to the other point. It’s also helpful in detecting a short circuit condition.
Later, the multimeter is used to measure the voltage and current at the desired points on the board. After this, the power is switched on and then the code is tested for errors by determining the readings in the form of 0 and 1. Overall, there are different phases depending upon the complexity of the project whereby testing has to be conducted until everything starts working as per the plans.
10. Working with wires
While taking on electronic projects, you will come across situations when you’ll have to work on the wires by cutting and stripping them. For this purpose, there are various tools available in the market but it’s important to select a proper tool so that no damage is caused to the components or circuit. Following is the list of wire strippers that you can choose from.
11. Power Source of the project
12. Ensuring safety
Ensuring safety is always important irrespective of the kind of project and the expertise level of the user. However, the beginners need to pay special attention as they have a lack of experience in handling situations. So make sure that you go through the following tips for that
• Wear safety goggles and gloves when the situation demands so.
• Make sure that the power is switched off before working on the circuit.
You may read our blog and article section for more topics on electronics engineering, industry, and technology.
Filed Under: Tech Articles
Questions related to this article?
👉Ask and discuss on Electro-Tech-Online.com and EDAboard.com forums.
Tell Us What You Think!!
You must be logged in to post a comment.